A3889VRA Admiral Range - Instructions

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

KILL POWER FIRST. I should have read other entries on here prior to starting. I would have learned that one leg of the element is always hot. Fortunately it arced against the oven, and all I had to do was replace the terminal. Could have been much worse. Unplug range or shut off circuit breaker prior to doing any electrical work. Verify 0 voltage before starting if you shut off the breaker.

During normal use, the heating element on my electric range burst into flames one day. Judging from the internet, this is actually fairly common! It's an electrical fire, so it's important to shut the oven off at once, and not a bad idea to cut the circuit breaker immediately. Then put the fire out and unplug. Remove what's left of the old element by unscrewing 2 mounting screws where it enters the oven rear wall. Taking door off of oven made it easier to lean in there. Then pull the crimp connections apart to get the wires off of each end. There are videos on youtube and partselect.com showing how. One thing they don't mention is that the wires may want to disappear back into the hole in the oven wall once they're loose. So hang onto them. I put a piece of duct tape around each one to keep it from slipping back into those small holes. When the new element arrived, I just reconnected the two crimp connectors and re-mounted the two screws. Of course, make sure range is unplugged while you're in there. Those two wires have 220V on them. I'm also never again going to leave my range on, either in baking or cleaning mode, when I'm not home. That fire was scary!

just removed two screws installed the unit replaced the two screws

Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

followed your excellent video and the job was a breeze Thank you !

Oven is built in. The only way to access the hinges is to pull the oven out and remove the sides.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.