A3832XRW Admiral Range - Instructions

the 1st thing to remember is to turn off the breaker for the stove then open the oven door and remove the racks and the heating element was there on the bottom undo the screw on each side where the element goes into the back wall of the oven and pull gently out and take your plyers and remove the wire hooked on each end becareful so that the wire does not fall back into the hole place your new element into the oven and plug the wire on the new element and slide it back into the holes and put back the screws and when done you can put the power breaker back on and try it this took less than 15 min.

Removed old gasket and replaced with new gasket'

Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

I viewed the video you sent [ which will bring me back to you for all my appliance parts ] and could have done the repair in less than 15 min. but one of the leads on my oven was too short so I had to disconnect it from the terminal to connect it to the new element and feed it back through the oven wall and reconnect it to the terminal. I will recommend you with out hesitation. Thanks, Tom P.

Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.

The oven heating element blew out on Thanksgiving... it went in style sending pieces of molten metal around the oven. After a thorough cleaning and removal of debris I obtained a replacement element. Replacement is easy. There are two screws that loosen the element. The connectors are a push-fit. The oven works great now.

I removed the element by removing two screws. I discarded the old element and installed the new one using two screws - just as shown in the video. I ordered the part and received it in just a few days. The price was good. Very happy.

Remove racks, remove 2 screws, pull element out, disconnect connectors, reinstall new element.

part was sent quickly and it was easy to remove and replace. also watched video

Turn off the oven and let it cool. Remove the door by pulling it upward. Remove the racks and pull out the drawer under the oven and set aside. You should be able to reach the electrical wall outlet. Unplug the unit. Unscrew the metal tabs holding the element to the rear of the oven. Pull the element out about 2 inches so you can reach the clips attached to the wires. This is why you must unplug the stove. Wiggle the clips until you can pull them off the element. Don't let them slip back into the insulation. Bend them upward if necessary. Replace with the new element. Put on the clips. Ease back into the insulation. Replace screws. Plug back in and you are good to go.

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.