Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Agitator in washer wobbles
Loosened the set screw and removed the agitator, found nothing wrong. Replaced the agitator and tightened set screw, no more wobble. This is a mid 1970 Maytag and a workhorse.Had three kids wash over the years, now "kids" in their late 30's and early 40' and washer is as good as new (except a little rusty)
First time I had a problem with it. Sometimes just look for the simple things !
Part select refunded me for my part that I ordered very fast.
Unplug washer and shut off water valves. Remove water hoses from the faucets and caught the water in the hoses in a bucket. I removed the drain hose from the back of the washer and caught the water in the bucket. Remove front panel by removing 2-screws at bottom and tilting it out to come off. Disconnected the hoses to the pump and caught most of the water in the bucket.. An old towel stuffed under the bottom pan of the washer, under the pump hole caught most of the rest of the water. Tip the washer on its back and removed the belt coming from the motor. Removed 3-screws that hold the pump on and angled the pulley end through the hole in the bottom of the washer. I just reversed the procedure to install the new pump and everything else. I would have replaced the hoses and belts, but I had just done that about a couple of years ago, when I replaced the connector at the top back of the washer for the hose from the pump and hose to the drain in the wall, that had a crack in it and was leaking.
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.
Agitator won't move, belt wore out after 24 years.
Removed 2 Philip screws from bottom front panel. The belts came as a set, so pay attention to the belt sizes when replacing them. Have had the new belts installed now for a week or longer with no issues. Looks like a good fix.
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00
waterpump leaked where plastic housing upper and lower halves were bonded
new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..
Washer is 27 years old. The washer lid bumpers were just worn out with age. It has been in constant use all these years raising 4 children with no other service or repairs. It has a matching dryer with the same track record. What a testament!
Removed the front panel with a screw driver, removed the old bumpers with a pair of pliers, replaced the bumpers and replaced the panel. All was very simple and took no time. The video on your website was most helpful. Thanks
Remove 2 screws from bottom of front panel, swing panel out and lift off. Remove 2 hex head screws from inside front corners. Lift top to expose injector in left rear corner. Remove clamp, remove injector from air break box then use screwdriver to pry the lip back through the hole in the tub. Carefully squeeze the lip of injector through the tub hole. Silicone grease or liquid detergent may help. Then reattach the injector to air break box and reassemble washer.
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal. Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Washer would not agitate, smell of something burning
Based on info from website, sounded like it was the Belt Kit that needed replacing. While waiting for the Belt Kit, decided to take the Agitator out to have a "look-see". OMG! There was liquid fabric softener gunk so thick in, around, underneath the agitator that the unit could not get traction. The burning smell was the gunk getting hot as the agitator tried to work. After a thorough cleaning of the agitator and anything relating to it's ability to agitate, my Maytag is performing like it was brand new! I'm keeping the Belt Kit, because my washer is older and I've heard from friends and family that have purchased the new water restricted units, absolutely hate them; like the "low flow" toilets, instead of flushing once, you now have to flush 5 times. They are washing more smaller loads and double rinsing each load to get their clothes clean and free of residue. I'm a 69 year old woman who finds your website and your marvelous contributors an absolute Blessing!