Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
When you open the door at the start the fan wood come on
I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it
FIrst shut off the powere to the stove and microwave unit. Since it was a combination unit with the oven, I had to figure out how to remove the bezel around the combo unit (two torx screws in the frame, four screws below) then the screws attaching the microwave unit to the oven unit. Make sure you unplug the three electrical connectors before sliding out the microwave unit. Set it on its side. Underneath is a cover for the motor area secured with a screw and the motor unit itself held in by two screws. Unplug the motor making sure you plug it back in the same polarity. Not sure if polarity matters but best to be safe. All are very strightforward and reachable. Reassemble in reverse order, turning on the power to check that everything works before reinstalling the bezel.
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.
The two dollar socket set from Xmas 20 years ago had the right size socket..
Long arms are advisable.
The lower element still plugged in while the upper wires were just hanging there surrounded with fluffy white insulation fuzz, I wondered, " Could I bake a potato for my yearning and hungry family?"
When I explained the situation to my retired father in Arizona he said simply, "I wouldn't."
The new element popped in. It got really red, and, kinda like watching my toaster toast, the show was pretty much over after it heated up.
Single Heating Element Support Clip was needed to hold up the heating element in the oven. Old single heating element support clip broke and came out of the hole.
Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D
I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Micrwave won't run - turntable turns backwards when door opened...
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
