Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating
It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Getting the original screws out was a pain, but once I got them out I disconnected to old wires and attache the new wires. Installing the new igniter was VERY easy compared to removing th original one!
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Drawer was bent, bowl was scratched, burner was chipped
Followed instructions with replacements. Ordering was not that clear. Was asked the size of the bowls (large, medium, or small, and I measured them and all four bowls measured 9". I ordered 2 large bowls. However, that was not the measurment needed , it was the distance of the drilled hole and the igniter so I was able to use only one bowl. I have saved the other. Mary Alice Krueger Washington
stove top burner ignition spark progressively got weaker and then stopped on all but one burner.
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!
Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
The most difficult part of the repair was getting the front panel off. I needed to remove the top of the stove, which was easy but awkward - remove the two screws from each of the four burner bowls. Lift the bowls one by one, disconnect the wire and slide off the small clip under each igniter. Move the bowls and igniters out of the way. You will find a piece of sealant underneath the stove top covering the length of the front panel. You need to gently pry it off by lifting the stove top just enough to break the seal. Once the top is separated just gently move it to the back of the stove. You can now remove the 3 large screws underneath the front panel. There are also 2 screws under the plastic anchors that hold the front panel in place. Be careful, there are hidden screws in the back of each anchor, so don't break them. You just need to loosen them just enough to wiggle the front panel out. With the panel moved, the igniter switches are mounted over each knob. There is a spring washer clip holding them down. Gently pry off the clip of the damaged switch and disconnect the two wires. Make sure you put the wires back in the same order.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.