91132219101 Kenmore Cooktop - Instructions

I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.

I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Do not remove the gas line.

Take off the burner racks and burner covers

Gently extract/remove the ignitors from each burner. You may have to use pliers, but be careful. They are ceramic.

Once you pull out the ignitors, you can remove the ignitors from their wires using plyers, you may have to twist them a little.

To take off the top - use Star screw drivers to remove the burners

Remove all the burners.

The star screws, and the burners are the only thing holding the top on.

Take off the steel top.

That exposes the ignitor switch assembly.

Make sure you follow the positioning diagram that comes with the new part.

Thats it really.

I removed the gas, because I thought I had to, but you don't need to. You can do the whole job in 30 minutes if you are careful.

Hope it helps.

You'll have to

Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves.
Installation went smooth and easy.
replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date.

Repair to range went real well, Lifted range from

counter. Removed eight screws that secure burner

assembly. Lifted burners from it's position, and

removed igniters. Installed heat srink at burner

connections so as to ensure high voltage would

have no leaks. Removed insulation, and installed

spark module.. Reassembled unit, placed in

counter cut out, put 110 volt cord into outlet.

Tested all burners, everything worked great..

The repair took about hour and 15 minutes.

Have fun and be careful...... THE END

Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.

In order to replace the spark igniter switch and harness, order the appropriate model replacement part for your GE gas model. Turn of the circuit breaker if it is not already in the locked off position. Remove grates, gas covers, knobs and all from the cooktop surface. Unscrew all the screws with a clover tipped screw driver. Pull up and out on the 4 porcelain flints at each burner. Lift top up. You will see the part that needs to be replaced to your far right. Unplug it and remove it. Replace and connect the replacement. Reverse the process on opening the stovetop until everything is back in place as before. Flip your circuit breaker back on. Done.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spark module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..

Unplug!!
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.