89890 Jenn-Air Cooktop - Instructions

Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...

The Jenn-Air R201 is a stand-alone Range with 4 burners, 2 6" and 2 8". Two of the burners were out, one was simply electrically open, the others were badly worn. One of the switches was bad and 2 of the burner connectors were bad. I started by opening the breaker for the range at the breaker panel, and removed and discarded all the burners. The ring adapters were rusted on all 4 burners as well as the trim rings. All 8 of those were removed and discarded. The broken receptacles were replaced using the high temperature wire nuts. Caution: make sure the high temp wires are tightly wound together with pliers before putting on the high temp wire nuts. You must have a good mechanical connection before the wire nuts go on. Replacing the Infinite switch for one of the burners was frought with problems, since the push on connector at one of the terminals broke. I had to replace the push-on terminal and purchase a good quality crimp tool. Once that was done, I replaced the trim rings, drip bowls and put the new burners into their respective connectors. Hint: make sure that the indicator lenses are not cracked, or the indicators will not be held in place and can float inside the control unit and possibly short out. If they are damaged, replace the lenses. After checking all connections, the control unit was re-installed, and the range circuit breaker closed. The unit worked perfectly afterwards and looks like a brand new unit - only about 23 years old. One of the original infinite switches is now acting up, so that will need to be replaced soon. Thanks for having these parts, I saved a lot of money rebuilding this range!!

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

easy, drop in

Replacing the switch was quick and easy. It actually took only about two minutes.

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.

removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok

PS made finding an old bowl/ring adapter easy.

Set in drip and and plugged in element.