85978L Amana Refrigerator - Instructions

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

Very simple fix, remove 3 screws, two connectors to the old switch

Removed the old handle, did a little clean-up of the refrigerator door, inserted the new handle and used the old screws to secure it. The fit was perfect.

easy repair and looks great!!!
Thank you from a single Mom:-)

Removed the old. Took off the name plate from the old handle. Put the name plate on the new. Installed new handle.

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

removed 3 phillips jead screws. removed old hangle. cleaned around the site of old grime./ smile. positioned new handle, applied the 3 screws, tightened, and " whalah" like new.

Removed a small cover plug on the lower portion of the handle, removed three screws. Took off old handle, positioned the new one, replaced the screws and cover plug and that was it! Wouldn't have taken even 15 minutes if I hadn't dropped a screw and had to search for it - lol.

1- Remove food from freezer and store in ice chest
2- Turn off refrigerator
3- Remove freezer drawers, 2 drawers, no fastener
4- Remove freezer slide out drawer front , 2 screws
5- Remove ice cube tray holder, 2 screws
6- De-ice back panel with hair dryer / blower
7- Remove back panel in freezer, 8 screws
8- Defrost refrig coil with hair dryer / blower
9- Unplug Bimetal Thermostat, 2 wires, orang / brn
10- Remove Bimetal Thermostat from coil, 1 clip
11- Install new Bimetal Thermostat
12- Re-assemble, reverse order

First I removed the old handle by removing the 3 screws holding it in place. There are 2 on the top and 1 at the side of the door. When I began to put the new handle on it became apparent that the metal frame inside the handle was not aligned perfectly with the old screw holes. The plastic is not even with the door horizontally on the top, but it fits otherwise. Be careful not to over tighten the screws when installing. Pretty easy overall.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!