7WDF530PAYM1 Whirlpool Dishwasher - Instructions

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

The old filter simply unscrews and the new one screws in.

It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.

Snapped the new stops on. It took about 2 minutes.

Followed directions from YouTube video.

Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues

removed and installed cords with screw driver

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

went to utube