7MMGL6741TW1 Dryer - Instructions

First disconnect power to the machine. Remove lower access door locate the igniter connector and disconnect it. Now, remove the screw holding the igniter to the mounting bracket with a 5/16" box wrench, carefully remove the igniter. Replace the old mounting bracket but first start the igniter mounting screw in the new bracket, threading it in all the way and then removing it to make installation easier. Install the new bracket and then the igniter, Be very careful, the igniter is fragile. Holding the igniter securely, install the mounting screw. Reconnect the wire connector replace lower door and plug the machine in. Voila! heat!!

The dryer would come on but not tumble and then shut itself off. I called a repair man, who came out after a $45 visit and said the motor needs to be replaced. He said it would be $200 plus the service call of $45. I told him no thanks but still had to pay him the $45 service call fee. The name of the company I called was Cook Appliance Repair out of Louisville Kentucky. I then did a Google search on locating a company that I could order the motor from and found Part Select to be very reasonable. The new motor was $79. I went ahead and ordered the maintainience kit that included the belt, the two rollers with clips and the spring loaded roller. The clips were a little difficult to remove and put back on the motor. The videos on Part Select did help and I would recommend watching them prior to replacing parts on any appliance. I am glad Part Select had the repair videos and think that is going above and beyond by offering these videos. The delivery time was quick. I ordered on a Saturday and received the parts on Wednesday with the standard cheapest shipping. I am very pleased with the parts and Part Select and would definitely recommend Part Select and will use again on my next repair. Total spent including shipping was about $114.60. My dryer is now fixed and working great. Thanks Part Select.

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!

The repair could not have went better. Did just as video showed and it was up and running in 10 min..The video was very helpfull.

The hardest part is figuring out how to get the unit open. You have to take out the brackets that appear to hold on the timer section and you have to remove the screws under the lint filter. Once you have the top off then you remove the screws that hold the front panel on from the inside. I decided not to remove the drum it seemed like a lot of hassle, instead I went down and got a right angle screwdriver, the terminal valves are in the front of the unit and you only have to remove 2 screws to remove the retainer which holds them both in place. The drum is in the way so you can't use a regular screwdriver and the right angle is a bit slow going but I think it is actually faster than removing and replacing the drum for a novice like myself. Replacing the coils took about 2 minutes and then reassembly another half hour. But the Dryer works great again and for $70 it was well worth it.

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

DISCONNECT dryer from power source. Removed 2 screws holding lint filter housing, pulled top cover forward to release the two plastic keepers, raised the top cover. Disconnected two wires from the door switch, removed two screws holding front pannel assembly, slightly raised off of two hooks and removed. Supported drum by placing a strap from one side top under drum to the other side top. Removed broken belt. Vacuume any lint from under and around drum. Slid new belt over drum, under drum stuck folded end of belt through tensioner and on to motor pulley. Reinstalled front pannel assembly by lowering onto two hooks near bottom, removed support strap, reinstalled the two screws, hooked up wirind to door switch, lowerew top back in place inserted two screws back into lint filter housing. Plugged up to power supply. Test operate.

According to your site, we purchased the Door Switch and the Thermal Fuse as these two parts had the highest percent of "what could be wrong". Figured we would send one back if we didn't use it. The Door Switch was replaced first and the dryer worked! Two days later, the dryer stopped working again. Still had the Thermal Fuse so we changed that out. The dryer worked again! Both parts arrived sooner than excepted! Both parts were simple to replace! The diagrams were very handy. The picture of the parts assisted greatly and the video's were the icing on the cake! VERY glad that we ordered both! Will recommend to everyone! PartSelect is bookmarked should we ever need your assistance in the future!

Exactly as described in the video provided online. Couldn't have been easier to do. All businesses should supply their customers with this kind of repair option!

I watched your video online. And followed those instructions. It made it very intuitive and practical to follow. Believe me I am a novice but you made me feel like I am a professional.Thanks.

We bought a slightly used dryer, which kept running when the door was open. Trying to get the lid off, I broke one of the clips that held the top on. I gave up, and went to the internet. PartSelect made it easy to find my model and a list of all of the parts. They also had an on-line video that showed me the location of the secret screws that I couldn't find that led me to breaking the clip. After watching the video, the job was insanely easy! I was also surprised that their web site estimated the delivery of the parts at 1.8 days. I figured that this was an average, but the parts actually showed up at my door 1.8 days after I ordered them!

Disassembled entire unit, vacuumed out all the lint & dust.Removed beater bars from drum and cleaned. Removed old / broken igniter replaced belt. Re assembled.

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

open machine up and replaced the new belt.