7MMGE9959TB0 Maytag Dryer - Instructions

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

I inserted the clip

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge would be thru the roof.