7MMGD0600TB0 Maytag Dryer - Instructions

Pulled out the broken part than easily snapped the new part into place..

Viewed your video on line VERY HELPFUL, problem is the igniter will not stay on long enough to heat up. I just went back on your site and ordered a Thermal Fuse and a Cycling Thermostat for the machine but think it may be to old of a machine to keep trying to repair.

Probably could have went faster but wasn't sure on how it would go. Overall not to bad. I wish the manufacturing companies would include the breakdown of the applicances like they use to,that would have helped alot. On the front panel there are 2 clips that you have to pay a lot of attention to. Otherwise you will break them off. . Gaining access to the igniter clip was somewhat of a chore but if you go slow it goes pretty good.

Checked to see if heating element was warming up by checking through access hole on front of dryer,it was, you know because it glows,so replaced coils and it fixed the problem. Important note, buy the coils as a packet, almost half the price than buying seperately. Thx everybody who sends in info, this is a great site to save people money on fixing appliances

Watched video. Made this a very easy repair.Will use this site for next repair.

It Went well Part was very fragile

I did a quick research online and found PartSelect to have the best price. I ordered my part on Monday 8/6 and to my tremendous surprise FedEx delivered it Tuesday 8/7!! I did not pay for overnight delivery. My son happened to come by that day and he took a small flathead screwdriver, pried the old one out and inserted the new part. Done in 5 minutes! PartSelect will be my supplier from now on.

Watched that igniter glowed for usual 15 seconds. Gas did not flow so tested solenoids for ohm resistance across leads. One was bad, less than 1350 oms (as I recall). Ordered the M series coil (solenoid) kit at Part Select, arrived the next day. Replaced them in 5 minutes. Took about 15 minutes to vacuum lint + dust out base of dryer area. 5 more min to put front of dryer 4 screws in and mount dryer door!

1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valve opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012

It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!

the repair was an easy fix, I removed the two screws from the brackets holding the coils, disconnect and removed them installed the new coils connected plugs turned on dryer and I got heat not bad at all thank you for the help

After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of going to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.