Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the pump wasnt puping out the water
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
First I removed the two screws that hold the door handle in place. I then pulled the door handle off and replaced it with the new one. As long as partselect.com is around I'll be able to keep my appliances longer.
I took off the front lower panel and the top panel. I also removed the door. I used the screwdriver to remove the first spring and then loosed the screw on the second ring that holds the bellow in place.
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Whirlpool front load washer drum filling with water after use.
Followed the installation video instructions. Removed the washer top with a 1/4” nut driver torx bit. Shut off and unhooked the water lines to the washer. Took one screw off of the solenoid valve on the washer back. Removed the water line on the solenoid on the inside with a pair of pliers. Installed the new solenoid in reverse order. It took maybe 10 minutes to take off and replace. Very easy to do.
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should be careful when disconnecting the two prong electrical connector from the heat sensor. the two black wires can pull free easily. In that case, the rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe the orientation slots on both the male andfemale connectors - they connect one way only! I set the washer on it's face while effecting this repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Water slowly filling the wash drum and spilling out front of machine
Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.
Turn off water to the machine Unplug machine Pull machine away from the wall Remove the water inlet hoses. At the back-top of the machine remove the three screws holding the top on. Lift up top from the rear and remove it. Disconnect the hose connected to the water inlet valve. On the outside of the back panel remove the screw holding the water inlet valve. Remove the water inlet valve. Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes. With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.