7LSC8244BN0 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
mechanical seal leak in pump
your instructions in the video were excellent, but the shaft of the motor was too corroded to reuse.
Parts Used:
-
Don from Flagstaff, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer not agitating
Pulled cap off agitator,pulled plug out of inside of agitator, use socket to remove bolt,gently pulled agitator out installed new agitator
Parts Used:
-
Joseph from Lakeland, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
directional portion of agitator didn't turn
-
ronald from Plymouth, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Timer knob broke
-
Harry from Berkley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water leak
-
Tom from Milton, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Agitator stopped working
After about 4-5 years, the agitator cogs or "dogs" will wear out and cause the agitator to stop working-Simply pop the cap off of the top of the agitator with your hands by pulling upwards, remove the plastic cap at the bottom of the agitator-there are 2 plastic ears that you pull up on also with your hand, exposing a 1/2 locking nut. Use a socket and extention to unscrew the nut. Grab the bottom of the agitator with both hands and pull sharply upwards removing the entire assembly. Flip the assembly over to expose the four cogs. Replace with new, and reverse the procedure to reinstall the agitator
Parts Used:
-
kerry from madisonville, LA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Would not spin during spin cycle.
After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.
Parts Used:
-
James G from Crossville, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Motor Coupling failed after 20 years!
Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.
Parts Used:
-
Brian from Spring Hill, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!