7DU840DWGX0 Whirlpool Dishwasher - Instructions

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.

New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you

follow the video, no problem, however, its still not draining after the cycle is finish now I don't know what to do.

The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.

I USED A PLUMBER

Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.

Unscrewed old access panel from dishwasher. Took out insulation and glued to new access panel. Took off bottom panel and placed on new front access panel. New panel fit perfectly on front of dishwasher. Hard part was getting the bottom panel to stay on new front access panel, but hammered it in place protecting the new access panel with Styrofoam cushion. Took about 45 minutes from start to finish. Used DW-40 around screw holes, because of age of dishwasher and rust setting up over years (22 years old).

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking

Swapped out the old upper dish rack with a new one. A video made the change simple.

I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

Removed and replaced leaking water inlet valve, 10 minutes and saved me a hundred in plumber fees.

Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.