7DU1100XTSQ5 Whirlpool Dishwasher - Instructions

We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.

Remove power to the machine. My particular installation did not require physically removing water and drain lines. Remove the dishwasher from the cavity. Put a towel or two down on the floor. Lay the washer on its face on the towels and this orients the motor in the up position on the bottom of the washer. CAREFULLY unplug the motor wiring harness but if possible, leave the heating element connection in place as spade connectors tend to lose their grip with multiple engagements. Remove the single bolt located between the motor and stainless bottom of the cavity that locks the motor in place. Leave it in the cardboard shield, that really helps in reinstalling it. CCW rotation of the motor disengages it from its housing. Work the motor straight up and out of the housing. This was the most difficult part of the entire process due to the metal housing not quite clearing the plastic pump housing where they mate, but its do-able. Nothing should have to be forced. Now you have the motor in hand. Be very attentive how and what order you disassemble. Remove the back of the motor housing to block the armature to remove the impeller. DO NOT NICK THE FIELD WIRING IN THE MOTOR. I believe the threads were left hand but I don't remember the rotation. They do tighten in the direction of the motor rotation though. Carefully pry the seal out of the pump housing with many short lifts as to not mar the housing itself. Added a little dishwashing detergent on the outside of the new seal and carefully pushed it into place with the end of my screwdriver. Don't cut yourself on the metal insert in the center of the seal.Reassemble the impeller to the shaft WITH the spacer that comes with the new impeller kit. Make sure the impeller is tightened down completely to the end of the threads to insure proper clearances when reassembled. Don't force or over tighten. You'll feel a positive stop. Reassemble the motor to the housing Lubricate the housing o ring seal on the outside with a VERY small amount of dishwashing liquid lest you create a suds factory on startup. Replace the holding bolt on the pump housing. Reconnect the motor leads and heater element if removed. Stand the washer back up. There will probably be water around the door area from the pump when the machine is returned to the upright position. Reconnect lines and check under the pump housing for leaks while in operation being careful not to get into moving parts or electrical connections. Good luck.

Due to the posts on this site, I took the advise of replacing the chopper assy. Old chopper did not look bad and seemed to function. Apparently I was wrong. After new chopper was installed, dishwasher worked fine.

Rmoved door skin to dishwasher. Then remove screws on the back side of the detergent/rinse aid despenser. Remove old despenser and install new one.Install all screws. Took about 15min. Very easy fix.I recieved the part very rapidly , Thanks partselect.com.

Disconnected the power. Removed the dishwasher mount screws from under the counter. Slid the Dishwasher out. Removed the two wires. Loosened and removed the two heater support nuts. Removed the heater element from inside the dishwasher. Placed the new heater element inside. Tightened the nuts. Attached the wires. Pushed the dishwasher back in place. Replaced the under-counter support screws. Reset the diagnostics message on the dishwasher front panel (This may not be necessary for some) - (Press HI TEMP > AIR DRY > HI TEMP > AIR DRY). All works great. Thank you PartSelect.com for fast shipping and great pricing.

put new on and tightened correctly -was nice to get the right part the 1st time !

replaced gasket

Pulled the dishwasher out, removed 2 wires and 2 plastic nuts, removed old heating element, installed new heating element, applied nuts, connected 2 wires pushed the dishwasher back in, drank beer (Per instructions on email - really liked).

As directed online

Removal and replacement of the gasket required no tools and took very little time. However, this did not solve the problem. I called in a repairman who determined the issue was the washer was not filling to the proper level. The control board was replaced and the problem was solved. This also quieted the washer a lot in that the pump was no longer sucking air.

Found problem when rack fell into dishwasher. Check for parts availability on Internet and chose partselect.com. I have used them before to order a locking tab for the silverware holder. I Placed order for current problem in late afternoon and parts were in hand within 48 hours. Video instructions made repair EASY for me. I couldn't ask for better service. As my appliances age I am sure I will be using partselect.com again.

I watched the video on your website, and I followed it to the letter. I find the service provided by this company extremely valuable to a person that is capable of doing his own repairs. Thank you, JAK.

Repair was straight forward. The video description was excellent. Pay attention to where the chopper assembly sits in the cavity, there is a second location closer to the impeller, but this is not where it goes.