79747 LG Refrigerator - Instructions

Slid new bin into place. It works perfectly now.

The ice bin I ordered did not arrive on time and, when tracking indicated it was delivered, it was not here. I notified customer service and was told that they would cancel that order and I could order again.and make a payment, to include shipping, again and I would be reimbursed. Two days later the first order showed up. I notified customer service that the item had shown up and I installed it therfore requested the second order be deleted. Was told that it was already enroute and they would send me necessary paperwork to return it. upon receipt of the paperwork I followed the instructions bur, when I contacted UPS (as directed) was advised that I would have to pay shipping of about $19. unless Partselect requested and paid for shipping and sent me the shipping label. I received the shipping label but, when I contacted UPS was advised that I would stoll have to pay to have the item picked up at my house and, unless I wanted to pay that cost I should deliver the package to a UPS pick up location........all the way across town through heavy traffic, about 25 miles. I should have kept the second bin along with the first, given it away or thrown it away and the cost would have been re imbursed. Trying to do the right thing, I was responsible for additional cost and aggravation .......Thanks a lot!!!!

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Remove back door and then shut water of to the refrigerator. Then remove old valve. Have towel ready for excess water when you remove nut to valve. Install new valve screw to refrig. Turn on water and check for leaks.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Examined old ice maker. It is held by some Philips screws. There are many screws you don't need to unscrew so look carefully. Then disconnected th dual in line connector. There is a little push tab to squeeze to release. Then the ground is connected with a screw. It's a little hard to see but unscrew that. My replacement came with no instructions or screws so try not to drop the screws down in the netherlands of the fridge. The hardest part was maneuvering the icemaker to reattach the power and ground. Even with that pretty straight forward replacement.

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.