79681022900 Kenmore Dryer - Instructions

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worked together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.

R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.

Seemed to be shutting off on the safety thermostat so I replaced them all. Works.

Removed the heating element, tested it, purchased a new element and installed.

After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cosume much time. I'm a women and it was easy to fix.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.

Unscrew and replace locker hook and assembly, replace screws. That completes door locking assembly repair. To replace the rollers and safety switch assembly, remove back top and front of dryer. Detach and remove control panel and set aside. Remove blower tube at bottom of drum and set all parts and screws aside. Detach all necessary parts and depress belt idler pully underneath drum and remove belt. Remove drum and unbolt rollers on the front panel and also on back of dryer. Remove triangular washer and be sure not to damage it. Check axles for damage, and replace new rollers onto axles. Replace all washers and triangular washer and bolt back onto dryer tightly. Be sure to check that all rollers are spinning freely and adjust bolt tightness accordingly. At some point replace dryer door safety switch by pushing it in from the outside. That completes the safety switch repair. Now once all rollers are replaced, reinstall drum and depress idler pully and reinstall the belt untiltension is restored. Reassemble all parts and plug all wiring back in to proper places. Screw everything back together, plug in dryer and start a cycle to confirm repair was effective. This is not a complete guide on the repair, just a basic idea of how I did it. I Googled videos on how it is done and that was of great help. The repair is actually pretty easy but is much easier with two people. There are some other steps but they should be obvious along the way. My dryer runs almost better than new and the repair was pretty easy and straight forward. It is most definitely a repair you can do yourself. Hope this helps you out.

with expert precision

Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.

Pull out dryer and unplug 220v. With phillips screwdriver, remove 3 screws from back of top and slide top panel back approx 2 inches and remove. Unplug 4 wire sets from rear of control panel. Remove 2 screws from back of control panel, carefully pull top edge and remove control panel. Remove 4 screws from top of front panel, as well as bottom 2 screws from inside dryer door. Disconnect door light wire near 10 o'clock. Pull top of front panel forward and lift off of tabs. Disconnect filter sensor wire under panel on the right. Remove 2 screws from each side of inner front panel and lift until tabs disengaged from side panels. Pull out bottom edge, carefully disengage inner front panel from drum and remove it. Try to turn roller wheels that are on the rear of the inner front panel. The wheel can get lint inside the wheel/axle and freeze. If one or both is stuck and won't turn easily, use a couple small flathead screwdrivers to carefully remove the plastic triangle retainer off of the roller assembly of the wheel that is stuck. You do not need to unbolt the axle from the panel. Wipe off the axle and inside of wheel with a clean, soft, lint-free cloth. If the wheel has a flat spot from being rubbed by the drum, you will need to replace it as I did or it will make a thumping sound after cleaned and put back together. Do NOT grease or oil the wheel/axle. This will lead to more lint collection and clogging/freezing. Reverse to put back together.