79571069011 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Parts Used:
-
john from locust valley, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light out
-
Jack from Ellenton, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My dishwasher was leaking water
The repair went well. They actually had to replace the motor. This saved me a lot of money having it repaired in this manner. Very professional & pleasant.
Parts Used:
-
rosalie from wayne, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring was broken on original unit, had to replace whole lever.
removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!
Parts Used:
-
Alan from Sun City West, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Parts Used:
-
Brent from ROGERS, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The gasket on our bottom drawer freezer was torn
Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!
Parts Used:
-
Pat from West Bend, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
interior lights stay on
Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .
Parts Used:
-
Rich from Pequannock, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker quit working
Removed 4 Stainless steel screw holding mounting assembly containing ice maker and motor. Unplug large plug from refrigerator inside wall and removed assembly. Closed refrigerator and lay asembly on flat surface. Removed ice maker plug from wire harness. Unscrewed ice maker mounting screws from mounting assembly. Reversed process to install new icemaker. Be sure to turn ice maker plug assembly to fit in holder on back of assembly and tape back in mounting assembly so assembly wil go all the way back in the door without forcing. If done properly, the ice bucket will slide in easily and the door to ice maker compartment will close easily without any problems.
Parts Used:
-
Russell from Baytown, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!