79065319210 Kenmore Range - Instructions

My husband and I pulled the stove away from the wall and unplugged it. We felt it was safer to unplug the stove rather than turn off the breaker. My husband disconnected the baking element and checked the lead wires coming into the oven to see if they were damaged but they were not. He fitted the new baking element to the lead wires and tightened the screws on each side. It was really easy to repair and the video we watched on the internet really helped. As a Mom who bakes a lot, and I wanted to make sure that the oven temp was correct so I tested the temp three different times with my oven thermometer. Each time the oven temp was accurate. Parts Select Service Department was most helpful and I received the part within two days. I highly recommend them and I would use them again.

Husband watched Online Repair Video. Took him maybe 5 minutes to Repair.Thank yall very much.

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

First observed how the element attached to the oven. Then unplugged the range. Unscrewed it at both ends using my nutdriver. At the connection clips, simply pulled the element end away from the electrical wire it attaches to. Used a pair of pliers to pry loose the clips. Once separated, slightly bent the wire so it would not slip back into the hole that goes into the back of the range. Did this on both sides. Reversed the process to attach the replacement. That process is insert the wires into the connection clips, push the wires back into the range, reattach the element to the oven wall with the original screws, plug in the range. I commend PARTSSELECT for rapid delivery.

Piece of cake! Unscrewed the old, pulled it out, & put in the new element. Turned the oven on & presto! Oven can now bake!

Easy as one two three. Snap electrical wires to new element push thru back wall of oven and turn screws tight. This company was so amazing and my order arrived in a few days. I found you on the internet. Bless you all .

I went to video and followed instructions. I removed the holding brace securing the element in and pulled out old heating wire and installed new one that came a day after I ordered it. It was so easy and saved me over $100

First off the shipping was lightning speed and the repair was super easy anyone can do it.

All I did unscrew bolts pull out element wires detach them attach new element to the wires push them back inside the openings reattach bolts all done easypeasy and I am a 63 yr old woman

Removed screws,pulled off clips,reinstalled new element.

Took to screw out pull to wire's out push to wire's back on put the screw back on complete less than 5minutes

Quite easy and takes 5 minutes Remove racks from oven. Use a phillips screwdriver and remove 1 screw from each side of baking element. Gently pull baking element slowly or carefully so you do not damage wires, insulation around wires or so they don't come off element before you can reach them. With a pliers, hold the metal clip attached to wire and pull off of baking element. Make sure wire will not go back into back of stove. Pull off opposite side wire in same manner. Take new element, check the orientation of the element, make sure it it going in correct, and slide wire clip onto one end of element. Do the same thing with the other wire on opposite side. Carefully feed wire back into openings in oven while placing element back in oven.. Replace screws on each side of element to hold in place. Turn oven on so make sure it element is heating. I left my oven on 400 degrees to burn off anything that may have been on the new element during manufacturing so it would not leave or transfer an odor to food when using the next time.

Just plugged it in! The hardest part was finding the model number. It was inside the top of the stove,while cleaning, I found it-on the left hand side when you take out the burner pans. I searched this site, found the part and when it arrived I just plugged it in and it worked fine. I would say less than 5 minutes to fix this issue.

pulled out the range and unplugged the range from the outlet! removed the oven racks. unscrewed the heating element and pulled out the wire connections a bit so i could grasp the connectors better and so they would not go back into the holes. getting the bad element off the connectors was the most difficult part of the process - this is what took the longest for me. I used pliers to grab the heating element connector and wiggle until it came loose from the connectors. once off, it was pretty simple to re-connect the replacement element and tuck everything back and screw the element back onto the oven wall. WA-LA!! back in the baking business - kids and mom are happy again! temp needs calibrating, but should be able to figure that out....thanks much!

Just unscrew the two screws that attach element to back of oven. Pull element toward door until you see push on terminals. Pull both terminals off.