Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
part was spected for it's size and wattage for a custom built oven
I made a 4' h 3.5' w and 7.5' long powder / ceramic coat oven capable of 700 degrees f. the elements were chosen due to their size and capabilty. I am useing -5- 2950watt elements split on 2 40 amp 120v coil contactors regulated with a PID and thermocouople.
prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now
unpluged stove pulled offback of stove behind buner controles took knob off burner switch took off two screws switchout put new switch in then took wires one at a time off and put on new switch put backon pluged in it worked
Lift stove top cover up and support cover so it will not fall down unplug element put new one in close cover and turn burning on and watch the burner get red hot. simple job why call a repair man in. Vicki
simply unplug the old burner and plug the new one it. not many repairs this easy. the best part of the whole thing is that the part arrived the next day.
Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.
My original drip bowls were rusty and ugly on the two front burners.
I removed the old drip bowls from the top of the stove and replaced them with the new ones. I am not a handy person but even I had no problem doing it as I regularly remove them anyway to put them in the dishwasher to clean them.
Burner heating element would not sit level with generic drip bowls
I replaced the generic drip bowls with the ones I ordered here and the work perfectly. The heating elements now sit level and I am very happy with them. Very easy to replace.
Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.
if iever need to do this again i will unplug the stove and take the back off. iwill remove the spade connectors from the back and remove and replace the unit from the front. from the rear i will replace the spade connectors and the insulation . plug in the stove and make sure everything works. unplugthe stove, put on the back,plug in the stove and position it.
Three terminal blocks burned out (disintegrated) on electric stove
First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!