78546 LG Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken door gasket retainer
Go to this site on You Tube to watch the "how to" replace the gasket retainer. The retainer I needed did not come with brackets or the cam you will need. You will need transfer them from the old retainer to the new one. Not hard, just be mindful of position of the items you remove to put them back in place the same way. A metal rod holds the brackets and spring in place with a screw on one end to prevent rod from sliding off retainer. The cam has a screw that holds it in place, use from old retainer. If the old cam is not broken use the one from the old retainer. It is not hard and you will save $$$ that you would pay an appliance repair company.
Parts Used:
-
Claude from SAN DIEGO, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Parts Used:
-
Alma from Winterport, ME
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Parts Used:
-
Karyn from DURHAM, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Parts Used:
-
Tammy from HAGERSTOWN, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light out
-
Jack from Ellenton, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water line was leaking
-
Awilda from Staten Island, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water supply to ice maker leaked
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new
Parts Used:
-
john from locust valley, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower motor out on condenser
-
George from WHITE BIRD, ID
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior Light Would Not Turn Off
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Parts Used:
-
Thomas from Bay Shore, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lamp cover and case had melted
I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!
Parts Used:
-
Donna from Abilene, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!