75546 - Instructions

Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .

Replaces door switches - removed screw from door hinge cover, lifted cover and removed switch. Plugged in new switch and reversed process. Removed screws from light bracket. Attached new frame to slots in roof and used screws to attach. Clipped on light cover.

Very easy...just remove fruit/vegetable baskets, remove glass shelf and frame, Unscrew the 3 screws that hold in the metal rod from the old one and re-install it in new shelf frame. Voila. I was going to have to wait 2 weeks for a service call and then who knows how long while they ordered the part. Took care of it myself in 3 days - fast, reasonable shipping and part cost. Thank you!

Real Easy

the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!

The repair was easy peasy! Just fit it all in. Shopping here was just as easy. I'd delayed doing it for so long because I thought it'd be laborious but I found my appliance fast and the parts I needed quickly. The diagram you provided with part numbers helped a lot. Thanks for making it easy.

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

I replaced the entire plastic frame to fix the drawers. I'm frustrated that the design requires that I do this. Removed the metal bar that actually provides the support for the front of the frame and the drawers, etc. Three screws to remove and re-install. Easy. After removing the drawers, I just gently bent the drawer cover hinges to slide them out of the frame and tilted the frame out of the fridge. The glass just came out easily as it's not attached with any clips. I had to work to remove the clear plastic panels but a little careful persuasion and I was able to white supports out of the way and remove the panels. Then I removed the aforementioned bar and replaced the glass re-installed the whole assembly.

Removed white plastic trim and installed new latch / cam shaft

replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!

The part labeled as water tank was not pictured on web site, and when it arrived it was a large coil of plastic tubing wire-tied in an oval shape,not a blown p/e tank as original.The oval of tubing would not fit into the door compartment, because of the bulk of the actuating solenoid. No instructions were included. It was necessary to hacksaw the steel solenoid mounting bracket off the solenoid, then contort the solenoid into the compartment to get all parts inside the cover. new connectors had to be purchased, because the the tank/tubing coil was 1/4" od, while the original tank had 5/16"od connections.

Removed two drawers and drawer covers, glass shelf and door frame. Replaced in reverse order.

I removed the old shelf and disassembled all the parts, removing glass shelf, bins, doors, etc. for use with the new shelf frame. Unfortunately, I hadn't been able to find all the roller assemblies from the original shelf and didn't realize that they were not considered part of the shelf frame. So, after reassembling all the pieces that I had, I still needed to order one additional roller assembly and specialty screw. Knowing this up front would have saved me a nice chunk of time and additional shipping charges. Otherwise, the repair was pretty straightforward.

I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!

Simple replacement part.