72180599200 Kenmore Microwave - Instructions

You Tube

Used plastic putty knife to separate inside door plastic molding from metal door frame. Small section at a time starting from latch area. Worked the knife around door to separate plastic molding. Leave plastic intact near door hinges. Carefully separate out of the way the molding, and access Phillip screws with long screw driver. Replace handle and screw tight the screws. Push into place the plastic molding with your fingers until it clips back into place. The end.

Pried off the inner molding around the door to access screws. Attached new handle. reattached molding. Very easy

Pop old one out and replaced it with new one.

Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.

very simple

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

1. Removed unit from the cabinet. (2 screws). 2. Remove the outer microwave metal shell. (10 screws). 3. Locate and remove part. (3 screws). 4. Install new part and replace all screws. 5. Install unit back into cabinet. So easy. I will share this site with all of my friends.

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.

I found and removed the clip for the door - top on the inside (not easy to find) and then removed the door. Called support who told me to watch you-tube and there were good instructions there. Needed needle nose pliers to hold broken screw and a screw driver that could fit between the metal. Flat head and phillips are required. OH you should try to leave the screw in the hole as getting it back there is a PIA. Took about 20 minutes and I am challenged mechanically. Altogether, not too bad.

Easy as 1-2-3! Removed door from unit (top right hinge has an easy small lock that simply "snaps out" with a standard screwdriver. Placed door face down on table. Removed outer (perimeter) frame with standard screw driver, by plying up. Removed the two screws (to the handle) from the backside of door with a phillips screwdriver. Replaced with the new door handle and repeated the above steps in reverse. Done.

Called an appliance repair service

Very easy repair. I popped of the inside plastic door cover with a putty knife, removed screws to old handle, inserted new handle and reinserted screws and plastic cover. It was that simple. The complete job took me under 3 minutes.

Piece of cake. Pryed the cover off of the back of the door with a flat head screwdriver and then screwed in the new handle.