72-7657-23-03 Tappan Range - Instructions

Ordered new racks and replaced them.

I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!

No installation steps required. I did have very fast delivery of parts ordered.

get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

It was a replace racks not repair. No problem

Put a new one in.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!

This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.

First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.

Working on an old oven is difficult. Please expect the unexpected. The years of heating and cooling play havoc with oven parts. The screws holding the Flat Style Oven Ignitor become stripped. It took extra time to remove them. I had to go to the hardware store to buy replacement screws. Once I removed the old parts and had replacement screws the job was very easy.