686WK-EKSVW Admiral Range - Instructions

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!

I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....

Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

Overall, it was painless and easy with zero problems

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Very easy, video helped tremendously

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the part and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com