66475113611 Kenmore Range - Instructions

Removed bottom panel. Unscrewed igniter. Replaced igniter. Reinstalled panel. Started oven before replacing panel. Easy install.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed back upper cover, unscrewed retaining screw from module. As noted in a comment from another do-it-yourselfer, I replaced screw with a longer one and reinstalled module. Note that the replacement part is not exactly the same as the old one(the wires are located differently), I noted the wire color codes with the slot number and reinstalled them in the same slot number. Works fine.

We replaced the part. It was pretty quick and easy to install.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Bought new igniter.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.

I didn't. Don't know how to get to light bulb to change it for this specific model

Putting the drawer glides on was easy. My range drawer did not have any glides on so my drawer would fall out. The drawer glides popped right on the drawer. The glides for the track were easy to screw into the body of the range. I had to bend the tracks up a little on each side with a pair of pliers. One glide would go onto the track and the other one would go on top of the track. After bending them a little I was able to push them onto the track.at the same time.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Remove;
Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out.
Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick.
Oven racks.
Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out.
Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove.
Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes.
Reverse to install new ignitor.

I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.

The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.

I had found a good YouTube video and didn't use the app.

As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.

Just took the bottom cover off the bottom of the stove, pulled the old igniter and put the new one on.

This did not solve my problem.
What do I need to do next?