Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Existing icemaker would freeze up, stop making ice.
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
.screw held in the center of the rail,pull it out,slide the rail up off the support brackets on the door,unplug the old one & plug in the new one,slide on, & replace the screw! That Easy
Plastic post that pantry cover rotated on broke off.
Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.
The tab that is used to swing the cover on the lower tray broke off on one side.
First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.
Honestly, so simple . Removed the fruit / veggie drawers, glass shelf and the supports for that shelf. Couple of screws and nuts and it was off. As stated before... the most "thought goes into attaching the linkage for the temp adjustment on the right side . GREAT opportunity to CLEAN the up the fridge a bit!! Parts Select made this such a no brainer. Their Customer Service was really an added bonus!!
Refrigerator would cool for a very short period of time. Then the compressor would shutdown via internal thermal overload or high head pressure. This was caused by the lack of airflow across the condenser coils and compressor.
(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed
It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you
Ordered new fan motor Got part took fridge apart Result was the motor was running The fan blade had come off the motor Replaced the motor anyway and reinstalled the fan, working well
Removed old seal and installed new one. Whole job took less than ten minutes. Repair video made it very easy to do! Be sure to allow proper relaxation of new seal before install.
Part of our Mullion Rail broke and needed to be replaced
The part arrived as expected. I detached the existing mullion rail using a socket wrench and disconnected the wires, which was as easy as pulling two pieces apart. Then I connected the wires to the new rail, slid the part into place and used the socket wrench to secure it. As easy as could be and good as new! In total, it took a matter of minutes.
Gasket has 2 tabs on the side that opens. Both had torn. Also one vertical slit halfway up the gasket
Followed your instructions: gasket came coiled in the box and was slightly curled up. Both left & right side of gasket were linked. Followed your instructions to properly restore the shape. Pulling the old gasket off and installing the new one took just a few minutes
Loosen the top 2 screws, remove the bottom screw, unplug the wire harness, lift up the ice maker and remove. To install the new one simply reverse the removal procedure. Note: You may want to wipe the inside of the new one to remove the protective grease or discard the first 2 cycles of ice.