Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Defrost in freezer not working, ice buildup in freezer, refrigerator not cold
Had to remove screws inside back of freezer panel, took off old thermostat. This one had a different plug on the end that wasn't compatible, so had to cut that off and wire it to the old plug end. Piece of cake. Put back panel back on and back in business. Hardest thing was getting the screws out!
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Freezer was not staying cold enugh for ice maker to work. Discovered fan was not working to cool condensor. Fan motor would only run if manually turned.
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
Very easily removed the nuts holding the gasket to the door. Previously took new gasket from packaging and used a hair dryer to smooth the wrinkles from it, about 5 minutes. Installed the new gasket and adjusted the seating of the actual freezer door, for a proper fit. Now there is no snow in my freezer and the poor compressor only kicks on maybe ten times a day, as opposed to most of the day. Not to mention what the savings in electricity may be and extended life for my Amana. Should have done this two months ago. Service and shipping from Parts Select is second to none, with a website interface that makes sense- try most of the other online retailers and you will know what I mean.
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00
First I removed all the screws with the exception of the top row, these I just loosend.I made sure how the old one was installed before I removed it.I then used a hair dryer on the new one briefly to take out the shipping kinks.I removed the old one and put the new one in with a little adjusting as i went. I then put all the screws back in,adjusted it a little more and finished by snuging up all the screws.It was very easy and works like new.
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!
I hired someone to do this, but after watching him do it, this is an easy job. Amana made a smart refrigerator and it's easy to do your self. I saved a LOT of money buying the parts here and I should have attempted it myself. The trick is heating up the gasket once it was mounted and then when you had a tight seal to the door, tape the door shut and LEAVE it as many hours as you can (minimum of 4, but overnight better).
Removed ice maker, then rear panel of freezer compartment. Removed old evaporator fan, cutting tie wraps as required.
Replace evaporator fan assy, paying attention to wire harness routing and secure harness with tie wraps. Reinstall rear panel of freezer compartment. Re-install icemaker.
1st remove the gasket from the packaging & let it get to room temperature . 2nd use a hair dryer to get it in shape . 3rd cut out a piece of the box that the door gasket was delivered in to cover the freezer opening after you remove the door,4th(remove the door by removing the bottom hinge) 5th put the door on a table to remove the old gasket with a screw gun,(now is a good time to clean the door up) after the old gasket & panel was removed I found the insulation inside the door panel frozen solid so I replaced it .If you don't replace this fiberglass insulation or a least try to thaw it out you defeat the purpose of the doors insulations R value. 6th replace the gasket (replace the gasket the same way that you removed it) 7th put the door back on the freezer.You don't have to remove the freezer door to do this job but it makes a much neater job & a better seal when the door is closed. This isn't the 1st door gasket I replaced so I kind of knew what I was doing.Good Luck
Constant Compressor Short-Cycle, Actual Unit Temp Colder Than Settings
Turn freezer section control wheel off, unplug unit. Then remove all items/baskets from freezer to allow access. Use nut driver to unscrew 3 screws on control plastic housing. Drop down housing from top and unplug wires (note correct locations) from control wheel switch. Remove screws and ground wire from metal backing plate to plastic housing. Push or pry the 2 metal holdtabs down carefully to allow the 2 plastic housing tab fingers to be pushed inwards to seperate metal plate from housing. Pry control wheel off from switch arm with screwdriver. Remove switch and replace with new one. Use the reverse order of removal above to replace into freezer but use caution when replacing wheel onto switch arm and plugging in wires. Remember to carefully pry the 2 metal tabs back up to secure the plastic finger tabs in place. Job done.
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98. So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one. But Parts Select is a great place to order from. Thank you.