51039 LG Refrigerator - Instructions

Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!

Very easy to replace right and left rail 3 screws on each side

Took off door per normal instructions.
Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door).
Inserted the new stopper and hinge assembly.
There was no locking nut on the newer part, so just had to level the fridge door without that part of the instructions (from normal LG instructions)
Overall easy for a non-handy person and the annoying sound is gone.
Wife is happier now.

First ,I unplug the refrigerator .
2nd i remove the back cover, clean the dust.
3th disconnect the water line, remove the all valve..
4th unplug all the wires and code ea with a No,remove the water lines
5th replace the valve reconnect the wires and water lines.replace the
back cover at last screw back the water line.check for water leaks .
i found ease the valve replacement installation.
.Thanks for the video.

Closed valve to water supply line; Removed contents of top shelf. Removed top shelf by sliding it out. Unscrewed old water filter and screwed in new filter. Replaced to shelf and contents in reverse order. Opened water supply line.

Replaced water pump assembly, all compression fittings easy to put together

Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver

Remove top shelf. Screw out old filter and install new.

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.

Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.

Just unscrew screws from old rails (still in refridgerator ), and screw them into new rails. We tried to order these parts from another online part site and we got the wrong parts. Partselect.com had drawing of our fridge and it was very easy to navigate through the web site. Thank you!