Models
>
51039
51039 LG Refrigerator - Overview
Models starting with 51039
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Guide Rail - Right Side
PartSelect #: PS3535267
Manufacturer #: MEA40002601
This is an authentic OEM part sourced directly from the manufacturer. The crisper slide rail for your refrigerator allows the crisper drawer to slide in and out, and supports the drawer as it does so....
$62.00
In Stock
Refrigerator Water Filter
PartSelect #: PS12714186
Manufacturer #: ADQ72910911
This is a single water filter that can be accessible inside the refrigerator. Water filters are designed to provide cleaner and betting tasting water, while also protecting refrigerators and ice machi...
$69.95
In Stock
Guide Rail - White - Left Side
PartSelect #: PS3535268
Manufacturer #: MEA40002602
The right side to this part is no longer available.
$32.51
In Stock
Water Inlet Valve Assembly
PartSelect #: PS3527457
Manufacturer #: 5221JA2006D
This water inlet valve has three solenoid valves and push in fittings. When energized this part releases water from the supply line into the ice mold.
$138.59
In Stock
Common Symptoms of models starting with 51039
[Viewing 3 of 3]Door won’t open or close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not dispensing water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evaporator Fan Squeeking
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin
... Read more
. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
Read less
Parts Used:
-
Kyle from WOODBURY, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench (Adjustable)
13 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice chute would not open.
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Parts Used:
-
Steve from MUKWONAGO, WI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
11 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Guide Rail
This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it
... Read more
out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!
Read less
Parts Used:
-
Nicole from BROOKSVILLE, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!