All Installation Instructions for Whirlpool Range 4RF302BXGQ0

element not working properly

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Parts Used:

Broil Element

PHILIP from NORTH PORT, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Removing an heating element that burnt into .

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Parts Used:

Oven Bake Element

Jenny from GREENFIELD, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven heating coil snapped and would no longer heat.

It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!

Parts Used:

Receptacle Kit

Diane from Gillett, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broke drawer bracket

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!

Parts Used:

Front Drawer Glide

Valerie from ROCHESTER, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bake element was broken

Remove the old part and install the new part.

Parts Used:

Oven Bake Element

Screw (Grnd Wire / Back)

Alexander from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The part doesn't seem to fit the glass door

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

Parts Used:

Oven Door Trim Kit

George E from SEVIERVILLE, TN
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace aged Drip bowls

Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

ROBERT E. from GLENDALE, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove burner burned out

Very helpful customer service Lady.
Helped me select the corect burner replacement.
And helped me get it ordered.
Repair went very well.
I recomend Parts Select if you need parts for.

Parts Used:

Surface Burner Element - 8 Inch

Ben from MONTICELLO, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The side trim on the glass door needed to be replaced.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Parts Used:

Hinge Pin Kit

Mary from LARAMIE, WY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My drip bowls were scorched and discolored and difficult to clean

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Claudia from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Main Power Terminal Block

Frank from Palm Coast, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used: