Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Eric M J - May 22, 2018
Verified Purchase
8" Whirlpool Electric Element.
The element (8") fitted perfectly, worked great.
★★★★★
★★★★★
Rosemary K - February 25, 2020
Verified Purchase
easy way of getting part needed and was easy to install
All is working great with my stove now.
★★★★★
★★★★★
Audrey V - June 7, 2019
Verified Purchase
Extremely satisfied.
Both burners were easy to install, and cooking has become pleasant, once again. Thankyou for the prompt service.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.7 / 5.0, 7 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Stove burner burned out
Very helpful customer service Lady. Helped me select the corect burner replacement. And helped me get it ordered. Repair went very well. I recomend Parts Select if you need parts for.
Ben from MONTICELLO, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost element clips and bad burner element
Pushed elements to remove them. Put on new clips by snapping on clips to all burner elements. Tilted each burner 60 degrees allowing room for the clip to clear the range hood and pushed the contacts on the burner elements into the electrical slot. Turned on each burner to make sure they work. All burner element's work fine.
I just put the drip bowl in and plugged in the new heating element and I was done. It heats much faster and is level now so cooking is much easier. Also the parts arrived sooner than I expected, so I was very satisfied overall. Couldn't have been much easier all around. I will use Partselect.com in the future. Thanks
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cecilia
November 23, 2023
My burner still works (8") but the "Y" bar it should be welded to, snapped off. So now it doesn't sit in the holder. Do I have to buy the whole unit?
For model number RF11OAXSQ3
Hi Cecilia, thank you for the question. Based on our research, the "Y" bar does not come separately. It comes along with the surface burner element, part number PS11747315. You may need to replace it to fix the issue. We hope that helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Fredy
August 1, 2017
Do u need to get a new plug???
Hi Fredy,
Thank you for your question. If the plug you have in the appliance is still working and not damaged then you can reuse the plug you have.
Good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lisa
February 1, 2019
This is the model number for a Whirlpool electric range. My question is this: Is there a specific surface heating element (8 inch) for home canning that can be used with this stove model?
For model number RF111PXSQ3
Hi Lisa, thank you for your question. Unfortunately no. You would just have to make sue you set your current element to the correct temperature you would need for canning. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Mary
December 12, 2019
The heat in my Roper left front 8 in heating element , goes straight to high ( when dial set anywhere from low to medium) and it will not regulate. I have to turn it completely off and start over. Will replacing the circular element fix this problem ?
For model number FEP310GWO
Hello Mary, thank you for your question. The issue is probably with the switch that controls that burner. We would recommend replacing Part Number: PS11740775. I hope this helps!
Was this helpful?
Thank you for voting!
Greg
November 10, 2022
The 8" coil sometimes heats and sometimes doesn't. Is this a problem with the coil or the switch? If it's the switch, is this something I can easily replace?
Hello Greg, thank you for reaching out. We recommend that you test both the element switch and the surface element itself to determine which part is defective. We have attached a relevant video to assist you with the element switch replacement. Let us know if you have further questions. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747315
Manufacturer Part Number: WP9761346
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Range-Elements-and-Burners.htm"},{"position":3,"name":"WP9761346","title":"WP9761346","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
