Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Although the motor was running, washer wouldn't agitate or spin.
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched between the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
i replaced the 2 parts listed above. very easily by using a 7/16 wrench to unloosen the bolt that holds the agitator base on. pulled it off (you have to pull a little hard) to unseat the base from the assy. looks like a tapered fit. then push the new one on. (make sure it bottoms out) then install & tighten the bolt. & then slide on the upper agitator
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
leaking drain pump. Obviously a common problem with this washer
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
I pulled theold aggitator off washer, pulled the cap off old aggitator, put on new aggitator, and put the new one on the washer. It was as simple as that.
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete. The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
1. unplug washer 2. move washer out from wall. 3. remove 4 screws that hold control panel; 2 screws on face and 2 screws an back 4. lift control panel to reach plug for lid switch and unplug old switch 5. open lid and remove 2 screws that hold lid switch on top opening; remove nut that holds ground wire from lid switch 6. remove old lid switch 7. new lid switch needs to be modified to fit in position,i.e. break tube surrounding wires of lid switch to be 1/2 length. 8. plug in new switch at control panel 9. screw in lid switch at lid opening and reattach ground wire. 10. screw control panel in place
knob was replaced - then machine is now working. we had been told that the machine parts were not available due to the age of the machine. We were ready to buy a new machine when our daughter went on your website and found the part. What a savings!
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.] Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.
Unplug power from wall. Disconnected water lines Tip Unit on it's side. (Recommend turning so motor is to the top side) Disconnect Electrical connector and Hoses from the pump and motor. Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry) Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth) used air compressor to clean up electric motor replace new coupling on motor and transmisison (may need hammer to tap into place) set rubber bushing on transmission side (transmission shaft should be facing up at this point) replace electric motor into place, making sure to line up bushing and motor mounts. replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.) replace electrical connectors and hoses connect washing machine power and water and test