Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 49-2847-23-01 > Parts

49-2847-23-01 Tappan Dryer - Parts

All parts for the Tappan Dryer 49-2847-23-01

Below is a list of all parts for the Tappan Dryer 49-2847-23-01 - Residential, Gas. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 49-2847-23-01
1-14 of 135
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$16.37

Rear Drum Bearing Kit

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$2.94

Door Latch Kit

The door latch is designed to keep your dryer door closed, even during the drying cycle. If your dryer door will not stay closed, the drying cycle might not start, or it could stop...

$29.32

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this installation include a Phillips screwdriver and a small flat blade screwdriver. A pair of pliers may also come in handy. Users ranked this repair as easy, and say that it will take fifteen minutes or less to complete.

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...

$10.64

Bearing Bracket

This OEM drum bearing bracket holds and supports the drum bearing in your clothes dryer. The bracket is located behind the dryer drum. Common symptoms that are linked to faulty or damaged drum bearing brackets include: the dryer will not start, will not tumble, or the dryer is making loud squeaking or grinding sounds. If there is an issue with the bearing bracket, it will need to be replaced. Replacing the bracket has been listed as a very easy to easy repair by many of our customers. Remember to disconnect the power to your dryer before beginning this repair.

$7.51

Flat Style Belt

This is a flat style ridgeless dryer belt.

$8.87

Grounding Ball

This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not operate, it is best to replace it to solve the problem. To repair, first remove the main top and remove the strap at the back of the dryer to lift the lid. Next, remove the two wire harnesses and Phillip screws on the sides that connect to the front panel. Now that you have access to the inside of the dryer, refer to the manual for further instructions by following the manual provided by the manufacturer.

$12.84

Idler Pulley Assembly

Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit you...

$22.09

Flame Sensor

This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off enough heat. If your clothes are not drying at a reasonable time, this might be your first indication of an issue. You will need to remove the two screws underneath the lint cover to remove the top of the appliance. Release the door switch wiring, remove the front panel, and remove the belt off the pully. You should now be able to completely remove the drum from the dryer. This will give you access to the sensor for the repair.

$20.11

Igniter

The burner igniter is used in dryers and activates or lights the gas burner to heat the dryer during a cycle. *Please note: Do not handle this igniter by the gray part, because it ...

$31.04

High Temperature Adhesive

This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before applying the adhesive, ensure that the area is completely clean from any debris and is dry. You may wish to use small clamps to hold the material in place while it dries. If the felt has come loose or broken apart, this may cause your dryer to make loud noise, indicating that new felt or rubber needs to be glued into place. Use gloves to apply glue.

$8.30

Grounding Ball Clip

This grounding ball clip is made of metal. Sold individually.

$36.35

Seal

Adhesive is sold separately.

All Parts for the 49-2847-23-01
1-14 of 135