3XARG493WP02 Whirlpool Refrigerator - Instructions

Needless to say sliding the new draw in did not take a wizard. But I was amazed at the ease of finding the part onb your web site and the promptness of shipping. Will definitely use you again if need be.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

The repair was very simple! And the website was also easy and accurate to use! I put the new rail in after taking out the glass shelf ( just like you do when you clean it) and snapped in the new piece. Voila! sliding drawers again.

Dear Part Select...What a wonderful easy experience....typed in model number...ordered part....it was affordable and arrived in 12 hours....snapped it in...booom.....finished....thaank-you!!!!!

Cut support and replaced. Easy

After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.

Replacement rail slipped into to the refrigerator in seconds! The best part of this story is the Excellence of customer service!!! After a long fruitless search for the replacement part, I found the website, ordered the part that I thought was appropriate. When I received it, i realized that it was too short. I phoned customer service, explained the situation and after giving the representative the make and model of my refrigerator, she promptly located the correct part and e-mailed instructions for return of the other part. I had spoken with the representative around noon on Wednesday and when I arrived home Thursday evening, the replacement part was already at my home!!!! I heartily commend this supplier. I had spoken to a representative when I first ordered the part. He straightened out a shipping address issue and was super! The second person that I spoke to was gracious and so efficient! I highly recommend this site!!!

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

put the replacement part in..........pretty simple.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Simple replacement, snapping the plastic rail in place and putting the crisper drawers back in. We were very happy that you had the part, your site made it easy to find, and it was shipped to us promptly, and at reasonable cost. Thank you.