3ED26MMXRWR0 Whirlpool Refrigerator - Instructions

Just replaced the grill with a new one.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

Friend did for me, had to take off door after disconnecting water like a power cord from top of door, now works fine, also did the cam on frig side too, works better also.

removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so much!

Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Simple read about three of the other peoples repairs,did the same and (PIECE OF CAKE)
Only problem ordered the cam kit with shipping over # 18.oo and only needed two pieces to do the job. Should have ordered just the two cams and saved a lot of dough.
But done and over with a happy camper (WIFE)

Very simple fix, remove 3 screws, two connectors to the old switch

By going on line and going to PartsSelect, the check out procedures traced the problem to the start/overload relay. Using a nut driver, I removed the back panel and using their instruction, I installed the overload relay. On the next to the last step on the instruction, the sealer in the kit was already hardened. I called the service hot line at PartsSelect and they apologized and sent me another kit to finish the repair. In two days, the new kit came and the repair was complete. The whole experience with PartsSelect was great.

easy - remove the door, replace th part, put back the door

Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.

Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line which we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.