3ED25DQXDN00 Whirlpool Refrigerator - Instructions

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Easy and amazed at how fast my order was processed. I received the parts next day. Wow!

watched the installation video twice and took my time to make sure all parts were put back together in the right order

The part fit perfectly. All I had to do was slide it in. Very speedy delivery and I am very satisfied with the service and would recommend your wedsite to anyone. Marie

replaced cam, new one broke after opening door 3 times...

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Removed front bearing(nut) assembled parts in correct order, the second time, attached bin front cover and all was good. Wife is happy again.

1. Slide putty knife under bottom of Ice/Water Dispenser cover (about 1-2 inches in from each side) and gently pry the cover from the tabs. Once cover is off, remove 2 screws holding water spout on so you can fit the new arm over it and the bracket. Remove the screw holding the right side of the water dispensing arm in place(no need to remove both sides since the left side just slides into place with no spring) with a nut driver and remove the old arm and spring. Position the new arm over the water spout and bracket, install the spring, right arm bracket and slide the left arm tab into the left arm bracket. Position the right arm bracket and install the screw. Re-attach the water spout, the cover and enjoy a job well done.

When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

A You Tube video described the repair steps and by following these instructions the whole process worked seamlessly.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.