3889VRV Magic Chef Range - Instructions

It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

Removed old gasket and replaced with new gasket'

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

Repair was super easy, Remove Screws. (the hardest part was trying to remove the edging of the door without cracking it, or breaking the tabs used to secure it) Once I got the edges off, I slid the front of the door off, removed the screws and braces holding the outer glass. Picked out the broken pieces, cleaned all the glass and inside the door and put it all back together. If I didn't clean everything, it would've taken half the time.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

There are five Phillips head screws to remove from the door (2 top, 3 bottom); the only touch part is that there are no screws on the sides, but instead plastic tabs on each side that "latch" inside the door frame; you have to use a flat blade screwdriver to work each tab and press on the door frame to unlatch each tab (yup I broke one, not knowing the setup the first time, but it went back together OK anyway). Once the tabs are unlatched from the frame, the entire front or the door will come off (be ready for this); then, just a few screws to take off the 2nd inner door glass frame (remove second glass carefully), and your to the inner glass, which just fits within the frame. Then, carefully backwards and the door is together again (once again, provide support as you take the last tab/screw off the outside of the front door, or you'll have more broken parts).

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

watched video provided when ordered part; follow the steps, easy as pie

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble