37-1022-66-04 Tappan Range - Instructions

Doris from SUN CITY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Left an appliance on surface element and melted paint onto the element

Plug the new element into the space on stove

Parts Used:

Kenneth from LANOKA HARBOR, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner would cutoff intermittently

Pulled out old burner/inserted new

Parts Used:

Surface Element - 8 Inch - 220V

Joseph from FREDERICKSBRG, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stem broken off old after market switch

Pulled control panel off front of unit and replaced switch wire for wire , went great because part sent was OME

Parts Used:

SWITCH

Gerald from MAITLAND, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

uneven heating

Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.

Parts Used:

Surface Element - 8 Inch - 220V

Dan from CHEWELAH, WA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner on stove stopped worker

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

Parts Used:

Surface Element - 8 Inch - 220V

Virginia from MT PROSPECT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

upper broiler

I haven't received the part yet! I would like to share with you about the installation but the part has not been delivered.

Plus, you are using my work email and I am not supposed to be using it for personal uses. I don't know how you got my work email. Please, change correspondences to my personal email:
dnkaren11@frontier.com.

thank you,
Mrs. Dunn

Parts Used:

Broil Element - 3000W 240V

Karen from SAINT ALBANS, WV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old drip bowls

replaced old drip bowls with new ones

Parts Used:

Vera from Snow Camp, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pulled the heating element on each burner installed the drip pans.

They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done

Parts Used:

Sharon from AURORA, MO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

This is for a basic four-burner electric stove:One element was bent so I replaced it and all of the drips bowls needed replacing.

The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!

Parts Used:

Olivia from FAIRLEE, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heating coils stop heating

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Parts Used:

Terminal Block Kit

Sharon from TEMPLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bilb went out

replaced it

Parts Used:

Light Bulb

Denise from Landover, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

2 burner elements not heating

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

Parts Used:

Terminal Block Kit

Brian from MENASHA, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pitted, Eroded Drip Pans

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Parts Used:

Josephine from Malden, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Left rear burner had a damaged burner prong.

I just had to plug the new burner plate in the receptical
and it works again very well.

Parts Used: