3626111193 Kenmore Range - Instructions

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

Stuck the dial/knob onto the existing stem for oven temp. control. Not exactly rocket science. It was harder to find the part than to install it.

removed two rear screws, pulled out range bottom, dropped new one in place, and reinstalled screws...VIOLA! works like a charm. I'm a woman and 53 years old ...If I can do it... you can too!

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Since I'm not very mechanical I had my service manager from work come to my house and fiqure out the problem. By using an electrical meter he found that there was no continuity in the igniter. So being the mechanical guy I am I watched him take out 2 screws that secured the the piece of metal that covers the bottom part of the stove. He pulled that part out and from there it was 2 screws to release it from the back of the stove and 2 more to disconnect the igniter from the burner tube. We ordered the part and it arrived in 3 days. I opened the box and to my dismay it was broke. I called to tell them that it was broke and they ordered me a new one right then. I had that part the next day very grateful for that. I was able then to put it back together myself and it worked. Wife is extremely happy with me.

Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.

Popped off old gasket and some retaining clips stuck but were easily removable. New gasket pops right in, super easy. Fits like new.

Very was ti replace racks and knobs. Very fast mail service

Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.

Found the Model information under the bottom drawer. Googled GE Range and rubber, found this vendor. Amazing, the replacement gasket was exactly as the original. Took the old gasket off with needle nose pliers, there were small metal clamps that had to be pinched together. Once the old gasket was off, the new one practically installed itself. Woman Power!

Baking is MUCH better now!

Ordered the part and put it on. My husband hasn't relized that i took care of it yet. One day he might remember to ask if we ever got the part. Very quick delivery.

You need to remove the knobs and remove the panel where the knobs are connected.

You also need to remove the display panel front to gain access to the where the electrode wires attach.

The other screws are readily visible. It's about 30 screws that need to be pulled.

The adapter put on the electrode can be pulled off with needle nose pliers and a small screwdriver, if the adapter does not fit through the opening on your stove. Just put the adapter back on after you snake the wires through.

Removed the drawer at the bottom of the stove, then removed plate in rear covering the wires. unplugged the 2 wires coming from Igniter, then removed 2 1/4" srews holding the ignitor in place, took the old Ignitor and cut the 2 wires and spliced them to the new Ignitor reinstalled the new Ignitor in reverse order of removal. Saved over $110.00.

1) Verified it was the broiler igniter that was damaged.
2) Removed the oven door, the lower pot storage drawer and the top range panel.
3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer).
4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first.
5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further.
6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results!
7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment".
8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner.
9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line.
10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.