Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 3521XRW > Instructions

3521XRW Magic Chef Range - Instructions

All installation instructions for 3521XRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3521XRW
301-315 of 393
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element burn-out

  • Customer: Herman from Payson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws on each end of the bottom element, removed blade wires from element and removed element. Put new element in to place in oven, put blade wires on to end of element and put in the two screws that held the element in place. Watched and followed the video instructions on the website. Very easy to repair.

bake element wasn't working

  • Customer: JEANETTE from MILWAUKEE, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When we received the new element for the oven. We followed the directions that where given to us and had no problem installing the new element. It took no time before the the oven was working again. thank you for posting the directions to make the job go easier.

Not heating

  • Customer: Darwin from wisconsin rapids, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

Two old Surface Burner Receptacles needed to be replaced.

  • Customer: Willis from Anaheim, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions given on your great site. Thank you so much.

Replace 8" Element Switch

  • Customer: John from Summerfield, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK

Drip bowls tarnished.

  • Customer: Jennifer from Albion, NE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Baking element burned out during self cleaning cycle

  • Customer: Roberto from Arvada, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
KILL POWER FIRST. I should have read other entries on here prior to starting. I would have learned that one leg of the element is always hot. Fortunately it arced against the oven, and all I had to do was replace the terminal. Could have been much worse. Unplug range or shut off circuit breaker prior to doing any electrical work. Verify 0 voltage before starting if you shut off the breaker.

Heating Element Caught Fire

  • Customer: Michael from Lawrenceville, GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
During normal use, the heating element on my electric range burst into flames one day. Judging from the internet, this is actually fairly common! It's an electrical fire, so it's important to shut the oven off at once, and not a bad idea to cut the circuit breaker immediately. Then put the fire out and unplug. Remove what's left of the old element by unscrewing 2 mounting screws where it enters the oven rear wall. Taking door off of oven made it easier to lean in there. Then pull the crimp connections apart to get the wires off of each end. There are videos on youtube and partselect.com showing how. One thing they don't mention is that the wires may want to disappear back into the hole in the oven wall once they're loose. So hang onto them. I put a piece of duct tape around each one to keep it from slipping back into those small holes. When the new element arrived, I just reconnected the two crimp connectors and re-mounted the two screws. Of course, make sure range is unplugged while you're in there. Those two wires have 220V on them. I'm also never again going to leave my range on, either in baking or cleaning mode, when I'm not home. That fire was scary!

elament burn out

  • Customer: Alton from Wetumka, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
just removed two screws installed the unit replaced the two screws

oven would not come up to temperature

  • Customer: Pauline D from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Burnt out bake element

  • Customer: Janet from Hillsboro, ND
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did it and was very easy. Has been done before too. Very fast service from you also. Will order again if we need to.

part of original burner not working

  • Customer: SUSAN K from SEDALIA, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
slide new burner in slot and turned on stove. Worked perfectly.

Door seal was pulled out by grandson.

  • Customer: Michael P from Hickory Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

The drip pans needed replacing.

  • Customer: Alison from Carnation, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Put in the new drip pan -- which are really nice shiny ones.
All Instructions for the 3521XRW
301-315 of 393