31FN-7W Magic Chef Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Stove top had burnt marks from long use
Just replaced the top.
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
Parts Used:
-
MEEWAN from BUENA PARK, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
-
Yafa (and David) from Bothell, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pilot light would go out when oven was turned off but still allowed gas.
l removed the top section after the grates. Then l took the phillips screws out of the three brackets which hold the L brace which supports the controls,thermostat and the regulator. Only because l did not have a closed-end ratchet wrench for 1/4" and l could not locate my 1/4" socket for my small rachet. l disconnected all gas lines and the thermocouple, then l used the power screwdriver without the apex which makes it a great power 1/4" nutdriver and took out the two screws holding the thermostat. Then l just reversed all the steps installing the new thermostat and once l got the air out and gas was pure l lit the pilot lights and everything worked great. And l adjusted my top burner pilot lights a little higher to prevent them from gettig blown out so easy. Done deal.
Parts Used:
-
Steven from Oklahoma City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
5 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas range knob and oven knob for my magic chief stove broke
After going to Homedepot, Sears, Lowes and other hardware stores I reached out to some folks at my job i was recommended to order the parts from PartSelect. I spent the Christmas and New Years Holiday in a mess. I really could not cook like i wanted to. I ordered the parts within a week it came. I am thankful you to guys no more drama, caos or worries. I highly recommend this site very easy to install. thank you
Parts Used:
-
Sandra from MONTCLAIR, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Parts Used:
-
Rhoda P. from Secaucus, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken burner knobs on stove.
-
Barbara L. from Tewksbury, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Install valve knobs
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Parts Used:
-
Donald from Peebles, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed a new knob
-
Clayton from Shortsville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new knob
-
Marvin from Pahrump, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Thermostat Knob
After ordering 3 or 4 different knobs for replacement, I found the one I needed. I did not have the oven model number at first...now everything is working fine. No tools, just push the knob into place. Thanks!
Parts Used:
-
Kathy from Fremont, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unable to see the numbers on the old knob.
-
Patricia from SAN LEANDRO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven knob was broke
-
Sara from FORT RIPLEY, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my knobs were broken on 30 year old range
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Parts Used:
-
Larry from LAWTON, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven control know wore out.
I purchased a knob that I was hoping might fit properly.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Parts Used:
-
Judy from ARDSLEY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace two stove valve knobs.
-
Roberta from BROOKLYN, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!