Models > 31FA-7-NK > Instructions

31FA-7-NK Magic Chef Range - Instructions

All Instructions for the 31FA-7-NK
16 - 30 of 51
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Parts Used:
Broil Pan Insert Broiler Pan
  • Rhoda P. from Secaucus, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken burner knobs on stove.
Just replaced the old burner knobs with the new !!!
Parts Used:
Valve Knob
  • Barbara L. from Tewksbury, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Install valve knobs
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Parts Used:
Valve Knob
  • Donald from Peebles, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed a new knob
pulled the old one off and push the new one on
Parts Used:
Thermostat Knob
  • Clayton from Shortsville, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Thermostat Knob
After ordering 3 or 4 different knobs for replacement, I found the one I needed. I did not have the oven model number at first...now everything is working fine. No tools, just push the knob into place. Thanks!
Parts Used:
Thermostat Knob
  • Kathy from Fremont, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new knob
Pulled one knob off and pushed the other one on.
Parts Used:
Thermostat Knob
  • Marvin from Pahrump, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unable to see the numbers on the old knob.
ordered it had to line it up then just popped it on.
Parts Used:
Thermostat Knob
  • Patricia from SAN LEANDRO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven knob was broke
Got the new one and put it on
Parts Used:
Thermostat Knob
  • Sara from FORT RIPLEY, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my knobs were broken on 30 year old range
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Parts Used:
Valve Knob
  • Larry from LAWTON, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven control know wore out.
I purchased a knob that I was hoping might fit properly.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Parts Used:
Thermostat Knob
  • Judy from ARDSLEY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace two stove valve knobs.
Inserting two stove valve knobs took 10 seconds! No tools necessary.
Parts Used:
Valve Knob
  • Roberta from BROOKLYN, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knob on older gas oven
The hard part was finding the parts, this oven seemed to have a temperature control knob that required a long fitting to reach the valve stem. The set of knobs I found on PartSelect were the only ones I could find. They worked great and took about 30 seconds to put on.
Parts Used:
Knob Kit - Six (6) Pieces
  • John from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Temperature numbers were worn off the old oven knob
I pulled the old knob off and popped the new one on! It was easy as pie!
The shipping was amazingly fast; I ordered the part on Easter Sunday and it was on my doorstep on Tuesday! Great service!
Parts Used:
Thermostat Knob
  • Rena from Cedar Rapids, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
Thermostat Clip
  • Willi from Old Saybrook, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Parts Used:
Light Bulb - 40W
  • Ivanka from Atlantra, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 31FA-7-NK
16 - 30 of 51
Back to Top