Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ignitor lights but gas does not come on
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves. The oven worked like a charm again.
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Lower burner failed to light, broiler running fine
Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."
Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perhaps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!
After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was harder than this.
