All Installation Instructions for Magic Chef Range 31213XAW

igniter waqs not working

was very easy did just as the video showed how to do

Parts Used:

Burner Head Cap with Spark Electrode

Flat Style Oven Igniter Kit

john from Corcoran, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Oven would not ligth, igniter did get red.

I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

Parts Used:

Flat Style Oven Igniter Kit

Fred from Juneau, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The oven would light, but the flame was very small and it took 30 minutes to preheat.

Watch the video, it's too easy and best of all, the part fixed the oven!

Parts Used:

Flat Style Oven Igniter Kit

Bradley from Louisville, KY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broke the insulator on the ignitor while cleaning the cooktop.

Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.

Parts Used:

Top Burner Igniter

David from Shelley, ID
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

burner head rusted out and not flaming properly

quarter turn with hand to remove old head...removed two wire leads attached to head to reattach to the new head...each wire fitting is different so you can't mess up...put on new burner head..quater turn to tighten...done...thanks...

Parts Used:

Burner Head Cap with Spark Electrode

David from Warwick, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Replace an old igniter

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

Parts Used:

Flat Style Oven Igniter Kit

Jacob from Agoura Hills, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Digital clock/timer broken

There were NO directions in the box, only a schematic. I was unable to locate the old one as my husband had removed it. So I had to guess which color wire connected to which plug. Good thing I guessed right the 1st time! so you might want to include installation instructions going forward.

Parts Used: