Models > 31203PAA > Instructions

31203PAA Magic Chef Range - Instructions

All Instructions for the 31203PAA
271 - 276 of 276
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Parts Used:
Top Burner Igniter
  • robin from saint marys, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Oven would not Light
Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.
Parts Used:
Flat Style Oven Igniter Kit
  • Dan from Clifford Township, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
slow to get to temp and slow to light
Followed the directions on the video. Very easy to do.
Parts Used:
Flat Style Oven Igniter Kit
  • Michael from Hartland, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Parts Used:
Top Burner Igniter
  • David from Shelley, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ceramic on spark igniter broken
Pulled cooking grate off, twisted burner head counter clockwise 1/8 of a turn, pulled up and out. Removed 2 connecting wires.put new burner head on in reverse order. Simple about 2 minutes including opening box.
Parts Used:
Burner Head Cap with Spark Electrode
  • John from Kelseyville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace an old igniter
Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.
Parts Used:
Flat Style Oven Igniter Kit
  • Jacob from Agoura Hills, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 31203PAA
271 - 276 of 276