31003SAW Magic Chef Range - Instructions

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

The burner head caps on my Magic Chef no longer work and had to be replaced. I ordered 1 of the 4 caps to see how it would work out for me. I did not have any issues replace the cap. I contacted PartSelect and order the other 3 caps. The sales representative took my order and was EXTREMELY helpful. Now I know why all of my neighbors choose PartSelect. Including the cleaning, it did not take me more than 15 minutes. The video was also extremely helpful. Our Magic Chef should be good for another 6-8 years. Thanks PartSelect.

turn burner cap counter clock wise lift out remove to leads,do not have to turn power off they are mini volts.Insert the two (leads)weirs on to new cap,twist back in done.Fire it up.

Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.

quarter turn with hand to remove old head...removed two wire leads attached to head to reattach to the new head...each wire fitting is different so you can't mess up...put on new burner head..quater turn to tighten...done...thanks...

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

took oven door off easy just lift up took bottom tray to oven out took bottom draw of stove out removed tin panel cover 2 screws to unplug igniter took 2 screws out of igniter and pulled unpluged wire through insulation. installed new igniter 2 new screws put wire through insulation and pluged it in. The only thing to check is matching the plug ends correctly before pushing them together.

I tried to get black drip pans to replace the ones I had which were well in need of changing. They no longer make the black so I found the silver ones on your site and thought for the price I would try them. They are wonderful and very reasonably priced. I ended up buying a spare set for later. Thank you for such great products and prices.

Basic instructions provided were accurate. Most difficult part was bending down and reaching across the oven door. A general information note would have been helpful. The circuit that feeds the igniter and the gas valve is a series circuit. So, even though the igniter was glowing cherry red, the igniter was still the cause of the gas not flowing, The voltage drop across the igniter was larger then normal causing the voltage to the gas valve to go down and to be insufficient to allow the gas to flow.

After watching your do-it yerself video, I turned off the gas and unpluged ac power cord, I removed the stove door and then removed the bottom tray inside the stove unscrewed tray plate pulled buner out of its housing. I then unscrewed the two screws to the old ignitor and unpluged it. Pluged in the new one screwed it to the burner bracket, put everything back togher then tuned on the stove. IT WORKS!!

Removed the oven burner changed the igniter reinstalled the burner still didn't operate,gave up purchased a new range. I liked dealing with your sales department very friendly.

This is one of the easiest home repairs I have ever done. I shut off the gas and unplugged the oven. I removed the door and shelves. I then removed the two screws that secured the igniter and pulled the connector through the hole in the back of the the oven. No need to splice any wires as the replacement igniter came with the correct connector. It was then just a matter of reversing the process. Very simple and quick fix.

Replaced the oven igniter and oven works perfectly 30 seconds to light