31-1449-00 ((02)) Tappan Range - Instructions

I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.

Very easy---simply unplug the burners, remove the old pans and replace with the new ones

I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!

When we bought our home less than a year ago, we had three functional burners on our 40" wide 50's classic Kelvinator (not close to standard size these-a-days). After a few months of use, two more burners went out for good and we were stuck using the back left burner for all of our cooking. I opted for the premium burners and made sure to compare my terminals with the ones online to be sure they mounted the same. I removed the burners and terminals, clipped the wires going into the terminals, and removed the top of the stove. I followed the directions that came with the new terminals, pushed in the new burners and viola! All four burners now work. I gave the stove a general cleaning and now my 1954 Kelvinator looks and cooks like it is brand new. It was easily the best $109 I've spent on my home.

was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

I simply removed the old drip pans and inserted the new ones which matched and fit perfectly.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.

This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.

removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy

Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.

removed element , cut wires, conected wires,replaced element

The range, (1988 Tappan) was givin to the church by one of our members. While using it, --after a period of time-- the wire burnt off to one of the burners. Since the couple gave us a brand new top for the stove that was still in the box, we decided to fix the stove up.
Now, with new wiring to all four burners, new shiney drip pans and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Just placed the chrome bowl trays in place and was good to go. They look very nice.

Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.

All you do it unplug the old one and plug in the new one.

There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.