30-4988-23-05 Tappan Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter was past-due for a change-out!
Just opened up the oven and went to work. Really easy repair. Removed floor of oven with two thumb screws. Removed flame diverter plate from burner with one screw. Removed igniter with two screws. Marked top wire, then untwisted old wire nuts to remove the old igniter. Replaced with new igniter and used enclosed new wire nuts. Reassembly was simply the reverse of above. Only issue - I needed longer arms to comfortably reach back into the oven!
Parts Used:
-
Kevin P. from Chanute, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Front glider ( plastic) on bottom oven drawer was proken.
I took the new plastic glider out of the bag and it took me about 2 minutes to fix the drawer!!! EASY!!!!! Thanks. carol
Parts Used:
-
CAROL from salt Lake City, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
oven not heating
Oven ignitor glowing but no flame . Tested ignitor w/ ohm meter reading 2.5ohms , should be 3.3 or higher to allow gas flow . Ordered new ignitor , replaces and jackpot !! Oven now fires and heats like new . Thanks for part . Cost , $50 instead of $150 .
Parts Used:
-
Mickey A from Linden, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
there were no problems
took off the front panel where the burner nobs are was very easy
Parts Used:
-
Richard from Oak Lawn, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Ignitor had a brunt spot in the center.
I use a 1/4 in. socket and and ratchet to remove 2 screws and removed cover to get to sheild to unplug the two wire plug . Then used needle nose to remove two conectors from the gas valve.
Parts Used:
-
Homer from Dayton, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Would not light.
Removed oven racks. Removed oven bottom and flame diverter. removed two screws and cut wires. Spliced new wires and reassembled.
Parts Used:
-
John from Munster, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker tray was leaking water from tray.
i took 3 screws from ice maker,then unpluged from frig.i then transferred cable to new ice maker and installed back into freezer. very simple.
Parts Used:
-
DALE from HAMBURG, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
I needed an extra oven rack to bake more at one time.
I just installed the extra rack and re-arranged the existing ones. Works great!
Parts Used:
-
Sally from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The oven igniter had become weak and would not ignite the burner.
Removed the oven racks. Unscrewed the two screws that held the oven bottom in. Removed the burner shield (one nut to remove). Removed the two screws holding the igniter in place. Removed the wires from behind and attached to the igniter. Removed the cover from corner that shields the wire and plug. Removed the plug. Removed entire igniter assembly. Cut and stripped the wires and wired back to the ends by using the wire nuts provided with the new igniter. Then just reversed the steps to reinstall the igniter! Yaay! It works fine. And I am a 66 year old woman with no help! I was very happy with the service and instructions provided by PartsSelect! Thanks!
Parts Used:
-
JOYCE from DAVIS, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven was slow to light and heat up
Replaced the oven igniter by removing the bottom oven tray (2 screws at back). Removed the 2 bolts that hold the igniter in place and cut the cables to it. Cut a little cable off the new igniter (cable supplied on the new igniter is long). Attached the new igniter with the 2 bolts and connected the cables together using the ceramic cable connectors supplied. Only thing to take care with is that you do not cut the cables too short and make sure to leave enough of a loop to join the cables together.
Parts Used:
-
Mike from Roswell, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!